DONGGUAN HUAXIAN LTD.
Professional Manufacturer of Vacuum Cooler, Ice Machine, Cold Room
Add to Cart
25kgs Blocks 5 Ton Salt Water Block Ice Maker Machine For Commercial Sale Ice Factory
Introduction
The brine pool block ice machine belongs to indirect ice making. The brine is used as the medium between the evaporator and the ice mold. The agitator is used to circulate the brine between the ice molds evenly to speed up the freezing speed. The ice-making tank is filled with prepared brine, and the temperature of the brine is cooled by the evaporator.
Add a proper amount of water to the ice mold and put it into the ice making tank, and use low-temperature salt water to freeze the water in the bucket into ice. The ice molds are fixed in a row, arranged in several rows, and fixed with steel frames.
The brine mixer circulates the brine in the brine pool, exchanges heat with the evaporator, lowers the temperature of the brine, and then exchanges heat with the water in the ice bucket to lower the water temperature in the ice bucket to below freezing point, after a certain period of time , all the water in the ice bucket freezes into ice.
Use the aerial crane to lift the whole row of ice racks that have been made into ice, put them into the ice melting pool to melt the ice and remove the mold, then use the aerial crane to place the ice mold on the ice dumping rack, and fix the rotating ice rack. fall off. Add water, make ice, de-ice, pour ice cycle operation.
Ice Tank Structure Description:
The technology of brine pool block ice machine is more mature, the failure rate is low, and the operation is more stable. In particular, the large-scale civil construction of salt water pools has a large ice production capacity, up to hundreds of tons, which cannot be replaced by other ice machines, and cannot be replaced in specific places.
The block ice machine for brine pool mainly includes ice making pool, ice making unit, evaporator, ice bucket assembly, ice melting tank, ice pouring rack, water adding device, aerial crane, cold storage, etc.
1. Ice-making pool: The ice-making pool is used to hold salt water solution, evaporator and ice bucket, etc. It is generally welded with 6-10mm thick steel plates, and the bottom and surrounding areas of the ice-making pool are designed for heat insulation.
2. Machine room: Mainly house the ice making unit, which can be fireproof and soundproofed according to customer needs.
3. Evaporator: Commonly used evaporators include spiral tube type, V-shaped tube type, and vertical tube type. According to the size and structure of the ice-making pool, the evaporator can be arranged in a centralized or decentralized manner during the ice-making process.
4. Ice Bucket Rack and Ice Bucket: Ice Bucket Rack is a steel frame resting on the ice making pool, which is used to put the ice bucket and lift the ice. The ice bucket is mostly made of 1.5~2.0mm thick galvanized steel plate, which can be welded, and the upper and lower ends of the bucket are reinforced with steel hoops. In order to facilitate deicing, it should be made into a rectangle with a large top and a small bottom. Anti-rust paint is required after the ice bucket rack and ice bucket are made and tested for leaks. According to customer needs, stainless steel can be used.
5. Agitator: There are two types of brine agitators: vertical and horizontal.
6. Ice-melting pool: The ice-melting pool is a rectangular pool welded with steel plates or made of concrete, and its size should be larger than the ice bucket rack. A swing frame is usually set in the pool to speed up the demoulding of ice cubes, and water inlet and drainage pipes are arranged on the pool to replenish high-temperature water and discharge low-temperature water. The ice-melting pool is arranged at one end of the ice-making pool on the ice-out side.
7. Ice dumping rack: The ice dumping rack is a device that overturns the ice bucket after melting the ice, so that the block ice slides out of the ice bucket. It is mostly made of channel steel, angle steel and steel plate, forming an L shape, and supported by bearings at both ends. Counterweights are installed at both ends to slow down the speed of pouring ice and reset it.
8. Water adder: It is a device for filling tap water or pre-cooled ice-making water into the ice bucket. The water adder is composed of a rotating nozzle corresponding to the number of ice buckets and a quantitative water tank to ensure that water is added to each ice bucket at the same time. The capacity of each grid in the water dispenser is 90% of the volume of an ice bucket.
9. Aerial Crane: The aerial crane should be a device that can move horizontally and vertically, and is used for lifting ice buckets when they are out of ice, filled with water, and put into the pool.
Parmeters
| No. | Item | Technical Data | |
| 1 | Daily capacity | 5000kg/24h (66pcs*25kg*3cycle) | |
| 2 | Cooling way | Water cooling condenser | |
| 3 | Compressor | Type | HANBELL |
| Power | 11.75KW | ||
| 4 | Ice plant Measurement | 7500mm(L)*3000mm(W)*3500mm(H) | |
| 5 | Equipment power | 17.5kw | |
| 6 | Cooling tower power | 0.55kw | |
| 7 | Water pump power | 1.5kw | |
| 8 | Circulating water pump | 3.7kw | |
Product Pictures
Applications
Ice Blocks can be used to lower high temperature of workshop, equipment, outdoor; Build ice structure and sculpture in snow parks; And it is widely used to keep fish fresh.
Customer's Usage Case
Our Service
After-sales Services
FAQ
1.How much weight of ice blocks?
Can be customized, 5kgs/10kg/15kg/20kg/25kg/50kg.
2.How many ice output cycles in a 24 hours?
3.Can you make ice storage room?
4.How to install the ice block making machine?
5.What is the payment term?